Vastex Big Red 4D 54" x 8.75' Dryer 

Big Red 4D 54" is a High Performance DTG, floor standing, dryers with Forced Air

Rated Shirts per hour

3 rows 1,425 or 2 rows 950 Plastisol

3 rows 648 or 2 rows 432 Waterbased or Discharge per hour

3 rows 180 or 2 rows 144 DTG White Ink

240V Three Phase - $2.28 hour to operate**

240V Single Phase- 98 amp 3 wire -

* 54" wide belt by 8.75' length

* Digital Temp Control

* Digital Belt Speed Control

* Cures Plastisol, Waterbased & Discharge Inks

* Up to 1,425 pieces per hour

* High Powered booster panel at enterance

* Unique cooling bed at exit, cools as garment exit the chamber

* Adjustable Heater Height

* 4 infrared panels, total 25,600 watts of heat

* 15 Year Heater Warranty

• Upgradeable, Add on additional Belt extension and heat chamber.

BigRed® 4D Series dryer 54 in. belt widths are the largest and most powerful dryers engineered specifically for DTG digital inks and/or screen-printed plastisols, water-based inks and discharge, making them ideal for Kornit® and other high-volume DTG shops, as well as automatic screen printing operations requiring high capacities.

Model BR4D-V54 with a 54 in. (137 cm) wide belt and four 48 in. (122 cm) wide heaters (total 25,600 watts) cures 180 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 648 garments/h with water-based ink or discharge, and 1,4235 garments/h with plastisol ink.

The capacity can be doubled, tripled or quadrupled by adding one, two or three modular heating chambers and conveyor belt extensions — as new or when needs grow.

For example, a model BR4D-V54 with four heating chambers can cure 720 garments/h printed with DTG/digital white ink at 2.5 minutes dwell time, 2,592 garments/h with water-based ink or discharge, and 5,700 garments/h with plastisol ink.

All BigRed D Series dryers feature a high-powered pre-heating zone that surges ink temperatures past 300°F (149°C) within the first several inches of conveyor travel, maximizing dwell time at optimum curing temperatures and, in turn, conveyor belt speeds and dryer output.

Air intake fans located below the roof of the enclosure quietly draw 'make-up' air into the chamber's double-walled shell through filtered inlets along opposite exterior sides at rates up to 560 cfm (15.6 m3/min), serving to cool the outer shell for safety, while preheating the incoming air.

An exhaust fan located below the center of the conveyor belt draws the preheated air downward at rates up to 900 cfm (25.5 m3/min), over the garment and through the belt, removing heat, moisture and contaminants from the chamber.

To accommodate each shop's layout, the 6 inch (152 mm) diameter exhaust fan outlet rotates 360 degrees for connection to ductwork, and the control box can be located on the right (standard) or left side of the chamber.

Exhaust filters located on both sides of the conveyor prevent garment lint from entering the blower or exhaust stack. Cleaning all filters before or after each shift can be accomplished in one minute, safeguarding printed images, the equipment and the shop environment.

Exhaust flow sensors with warning lights alert operators to a clogged exhaust line, clogged filter or blower failure. Other safety features include a light tower to monitor dryer status, and a 'cool down mode' for powering down.

Dual digital PID temperature controls maintain accuracy to +/-1°F (+/-0.5°C).

The heaters of the BigRed 4D dryers carry a 15-year warranty, and feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under curing associated with conventional uniit.