Currency
Shopping Cart

Call Us Now

HOTLINE: (404) 691-0015

Share

KMX Dischargeable Additive Base

In stock
SKU
KMX800
$15.00

KMX Dischargeable Additive Base

  • Waterbased Hybrid Discharge Base
  • Mix 50/50 with Plastisol Ink
  • 100% Cotton Only
  • Soft Prints
  • Cure 320F @ 60-90 seconds
  • Must use KMX Activator with product

The KMX Plasti Discharge additive is a unique water-based clear additive that is combined with a plastisol colored ink and KMX Discharge Activator to form a hybrid (water-base/plastisol) ink that will discharge the original color from the underlying fabric while simultaneously printing the desired new color in a single operation.

Selecting the substrate - Not all garments are designed to discharge. They must be “reactive dyed” and natural fiber (100% cotton). At the present time, most name brand 100% cotton shirts will discharge. Kelly Green and Royal Blue substrates have historically been difficult to discharge; however, recent testing indicates more positive discharge reaction.

Selecting a plastisol color - Technically, any plastisol can be used to provide the color. However, it is important to remember that the intensity of the color will be diluted by the 50% Plasti Discharge additive component.

Therefore, by using a high opacity color, the end result will be a more accurate replication of the original plastisol color. Kolormatrix recommends Super Advantage for the plastisol component. Test results with these inks have, in most instances, resulted in precise color matches.

Blending - Plasti Discharge additive is a hybrid product that combines an aqueous discharge base component with color, provided by plastisol inks. The two components should be blended at the recommended ratio of 50:50 by weight. This ratio will approach maximum color accuracy and coverage. However, printers can choose to alter this ratio to achieve to the desired finish, with a higher ratio resulting in a softer finish. This step can be completed in advance of production as pot life begins to diminish 6–8 hours after the addition of the activator powder. The amount of discharge agent powder should be determined by the weight of the amount of Plasti Discharge additive, rather than the combined weight of the additive and the ink.

Activating the Plasti Discharge additive Base - To activate the Plasti Discharge, add 5–6% discharge activator agent immediately prior to adding ink onto the screen. Some garments will discharge fully when as little as 4% of this activator is introduced; so, use the lowest possible percentage to achieve the desired effect.

Pot life of the ink at this point is approximately eight hours. However, to achieve optimal performance, apply in 1–2-hour increments and only activate the ink needed for the time interval allotted. For longer runs, the repeated addition of fresh Plasti Discharge activator additive to the screen will help to keep the process working at peak efficiency.

Curing - Discharge is a steaming/extraction process. It is very important the print is not cured using extreme temperatures Remember: longer dwell time is more important than higher heat. See “Testing the Curing Process,” below.

Testing the curing process - When the project begins, first run two prints down the dryer, then immediately run one of the prints through the dryer again. Then, compare the two prints; if the prints look the same, the dryer is ready for production. If the twice-cured print looks better, slow the dryer and repeat the test until they match. Remember, in the curing process, there is a plastisol component that still must cure between 300°F–320°F (150°C–160°C).

Therefore, in addition to steaming the water out to enable the discharge function, it is also necessary for the ink film to reach cure temperature. As the water evaporates, the plastisol ink will not reach cure temperature until the discharge process is complete. Thus, testing for complete cure is highly recommended.


This product requires the KMX Discharge Activator Powder.

Write Your Own Review
You're reviewing:KMX Dischargeable Additive Base
Your Rating
Brand Description
History Color sit amet, consectetur adipiscing elit. In gravida pellentesque ligula, vel eleifend turpis blandit vel. Nam quis lorem ut mi mattis ullamcorper ac quis dui. Vestibulum et scelerisque ante, eu sodales mi. Nunc tincidunt tempus varius. Integer ante dolor, suscipit non faucibus a, scelerisque vitae sapien.